Attaching things to EIFS

Attaching things to EIFS

Attaching things to EIFS is not rocket science but you need to know what to do

I had a lady call me the other day wanting to know the correct way to fasten her hose holder to the outside of her EIFS home. She could not get it to stay on the wall. This is actually a very good question, because there is a very specific way to install things to the outside of this cladding (Exterior Insulation and Finish System also known as Dryvit ® or synthetic stucco) whether it is a hose holder or a down spout for a gutter. First of all you are going to have to use a screw long enough to go through the system. Typically you will have between 1 1/2 inches to 4 inches to go through. You can tell how thick the material is by checking the bottom. The Synthetic Stucco will stick out from the wall and you can measure it there. Use a 3 or 4 inch screw and a 3/8 inch piece of PCV pipe. Drill a hole with a 3/8’s drill bit into the cladding where you want the screw to go. Stick the PCV pipe in the hole and make a mark where it is flush with the wall. Remove the PCV pipe, and cut it on the inside of the line as not to have the pipe stick out past the wall, but remain flush with the Synthetic Stucco finish. Apply adhesive (PL-Premium®, found at your local hardware store) to the outside of the PCV pipe and insert it in the hole you just drilled. The PCV pipe should sit all the way back to the substrate (OSB), and come out flush with the stucco surface. It is very important that the pipe is a tight fit, and the adhesive should be around the end that is outward at the Exterior Insulation and Finish System surface to make a good seal. Wipe any excess adhesive away with a damp cloth before it drys. Now, fill the pipe about half way with silicone caulk, and screw your hose to the wall using the holes you just made. When you screw the screw into the pipe excess caulk will come out the PVC pipe again use your damp cloth to remove any excess caulk that gets on the stucco’s finish coat or top coat. That is the old school way of doing it, and of course nowadays you have a fancy new way of doing it, and that would be a Corrosion Resistant Fastener and Sleeve Set. Myself I still use the PVC pipe and it works great, and like I always say if it ain’t broke don’t fix it. If I was doing a large house or building that had down spouts I would however use the Corrosion Resistant Fastener and Sleeve Set’s just to save a ton of time.

Well, there you go, that is the correct way of attaching things to your Synthetic Stucco cladding.

The last thing you want to do is just run screws into your this cladding system, as it will create penetrations that water can enter the system and cause problems down the road.

Have a Project? We can come out and take a look at it.

DIY EIFS – Do It Yourself EIFS Repairs

Attaching things to EIFS

 

 

 

Attaching things to EIFS / Dryvit ® / Synthetic Stucco

Becoming an EIFS Repair Customer

Becoming an EIFS Repair Customer

The easiest way of becoming an EIFS Repair customer is to have us do an EIFS job for you

That is certainly not the only way of becoming an EIFS Repair Customer. You can also buy the EIFS Repair kit, hire us to do EIFS Training  or subscribe to our customer area of our EIFS Repair Forum. If you have us come out, and do an EIFS job for you, or Train your guys you will automatically qualify for a free subscription for one year on our EIFS Repair Forum. Our customer area of the Forum is where you can access all the EIFS information and data you will ever need. The question and answer section of the customer area cover the most complicated and detailed EIFS questions from the finer points of EIFS Repair to Government studies on the product. Purchasing an EIFS Repair kit is another way you can qualify for a one year free membership to the customer area of the forum.

What if I have not purchased anything from EIFS Repair, but I still would like access to the EIFS Repair Customer Area of the Forum?

That is simple you can purchase a one year subscription to the EIFS Repair Customer Area for only $3.99 an month. Your subscription will allow you access to the entire Customer area of the site and the ability to ask your EIFS questions and have them answered by an EIFS professional.

<<< Click the subscribe button to to purchase your membership to the EIFS Repair Customers Area of the Forum.

We use Paypal, the famous Ebay Company for our Online Purchases, we will never have your personal information, it will all be handled by Paypal, so you can have complete peace of mind purchasing your membership.

Note: The EIFS Repair Forums cover all brands of EIFS / Synthetic Stucco including Dryvit, Senergy, STO, Master Wall, etc.

EIFS Repair Customer
© eifsrepair.info 2011 - Plagiarism Warning

EIFS Repair Customer

EIFS Certification

EIFS Certification

Your EIFS Applicator should be trained and have an EIFS Certification

Keeping up to date on the EIFS industry and it’s ever changing technologies is key to being a good applicator. Building codes are changing from year to year with the ‘Green Moment’ at the fore front of American Building. New standards and technologies are being introduced to the Synthetic Stucco industry like never before. Test data from the Department of Energy indicates Exterior Insulation and Finish System will be a formidable product for years to come to help America reduce its energy consumption from the building sector, which at present uses about 10% of the worlds energy produced.

Corey Turcotte, eifsrepair.info, A display of current Certifications by Industry leading manufactures and Universities including BASF, Dryvit, Senergy, Master Wall, Parex, Build Design plus Construction University, and Hanley Wood University
 

Dryvit Certifications

  Outsulation System

 

 

 

 

Dryvit Cert Outsulation Plus  Outsulation Plus System

 

 

 

 

Dryvit-Cert-Outsulation-X  Outsulation X System

 

 

 

 

____________________________________________________________

EIFS Certification

EIFS CertificationEIFS CertificationInfrared Thermography Inspection Training Course

 

 

 

 

 

EIFS Certification

Master Wall Exterior Insulation and Finish System Applicator Certification

Master Wall Applicator Certification

 

 

 

_______________________________________________________

 

EIFS Certification

Parex Applicator Certification

Parex Applicator Certification

 

 

 

EIFS Certification BASF Online Campus For High-Performance Construction

High Performance EIFS for Sustainable Construction

 

 

 

 

EIFS Certification

BASF Online Campus For High-Performance Construction

 Sealant Repairs that Last: Hybrid Sealants for Building Restoration

.

 

 

 

Spray Polyurethane Foam Air Barriers BASF Online Campus For High-Performance Construction

Spray Polyurethane Foam Air Barriers

 

 

 

 

___________________________________________________________________________________________

 

Hanley Wood University – Continuing Education & Training
for Architects, Builders, Contractors and Remodelers

EIFS CertificationProperties and Benefits of Exterior Insulated Finishing Systems (EIFS) – Sponsor, EIMA (EIFS Industry Members Association)

http://www.eifsrepair.info/wp-content/uploads/2012/01/EIFSBeniefitsCert.pdf

 

 

 

 

EIFS CertificationContinuous Insulated Claddings for Energy Efficiency and Architectural Diversity – Dryvit ® Dryvit Care ® 

http://www.eifsrepair.info/wp-content/uploads/2012/01/CaddingCert.pdf

 

 

 

                                                                          ____________________________________________________________

 Build Design + Construction University

BASF Sustainable Construction Academy

EIFS CertificationNew Developments in Concrete Construction

http://www.eifsrepair.info/wp-content/uploads/2012/02/New-Developments-in-Concrete-Construction-400.jpg

 

 

____________________________________________________________

An Overview of Pest Bird Deterrent Systems Certification

EIFS Bird Deterent SystemAn overview of bird deterrent products, along with the characteristics of common pest birds, bird problem assessment, and the issues and concerns associated with the roosting and nesting of pest birds.

 

 

 

_____________________________________________________________

 

EIFS certification

Note: All company names and programs are registered trademarks of there respected companies and in no way support or are affiliated with eifsrepair.info.  

EIFS Certification

Fiberglass Mesh – EIFS Repair Kit

The Fiberglass Mesh – EIFS Repair Kit

The importance of the Fiberglass Mesh in your EIFS Repair Kit

The Fiberglass Mesh keeps the EIFS cement from cracking. The EIFS cement coat is only 1/8 inch thick and would crack without the fiberglass mesh. The mesh gives the EIFS System strength and with it being fiberglass it has a heck of a lot of flexibility as Fiberglass Mesh - EIFS Repair Kitwell. When applying the fiberglass mesh you must overlap the mesh at least 2 inches and the entire foam has to be covered with mesh. Any places that are not covered with mesh are going to crack and spider over time. The Fiberglas mesh is also used before the foam is applied as a back wrap for all the windows and doors.   A 9 inch ripe of fiberglass mesh is stapled round each window and door with the mesh face out toward the window or door. Then the foam is fastened over the mesh and the over hanging 7 inches of mesh is wrapped back up onto the foam with the base coat. This method is called backing wrapping. Back wrapping is very important to help water and moisture from penetrating the EIFS System.

Note: EIFS (Exterior Insulation and Finish System) Repair – The Do it Yourself EIFS Repair Kit; for all Synthetic Stucco including Dryvit, Senergy, Sto, Parex, Master Wall

 

Fiberglass Mesh - EIFS Repair Kit
© eifsrepair.info 2011 - Plagiarism Warning

 

 

Fiberglass Mesh – EIFS Repair Kit – EIFS – Exterior Insulation and Finish System – Synthetic Stucco

 

EIFS Repair Kit – Do It Yourself

 EIFS Repair Kit – Do It Yourself 

Patch your own Exterior Insulation and Finish System with the original Do It Yourself EIFS Repair Kit

EIFS Repair Kit

Click Buy Now button to purchase the
EIFS Repair Kit

EIFS Repair Pro Kit

The Do It Yourself EIFS Repair Kit
Only $279.00
Pro Kits are now available. Click the link for more info
EIFS Repair Kit
                                                                                     

Click this Buy Now Button to purchase the EIFS Repair Kit                        
Pro EIFS Repair Kits
This link will take you to the Pro Kits

We have been getting a lot of calls from out of state with customers that want there buildings and houses repaired, but unfortunately, can not find anyone to do the work, Do It Yourself EIFS Repair Kitand they have no idea how to do it themselves. Well, those days are over because we listened, and now we have a great new EIFS Repair Kit.  The kit includes 4.5 lbs of our specially blended fiber glass based EIFS (Exterior Insulation and Finish System) material, mix container, stir paddle, trowel, float, gloves, paint brush, razor knife, foam, fiberglass mesh, AR glass fibers, 3.5 lbs. Fine Finish, 3.5lbs. Medium Finish, 3.5lbs. Coarse Finish, install instructions, and a  helpful DVD to watch before doing your repair. You will have enough material to cover approximately 5 Sq. Ft. of Exterior Insulation and Finish System repairs. Patching your Synthetic stucco has never been easier with the new Repair Kit. How to patch stucco.

For more info on The DIY EIFS Repair Kit Call 1-888-407-2609

DIY EIFS Repair Kit $279.00

    <<<<<  Click this Buy Now Button to Purchase Online DIY EIFS repair kit Small

Bundle your Repair Kit with our new book ‘EIFS Repair – A Comprehensive Guide By: Corey Turcotte. Bought separately $318.99 bundled you only pay $299.99.                  …  Read more

We use Paypal, the famous Ebay Company for our Online Purchases, we will never have your personal information, it will all be handled by Paypal, so you can have complete peace of mind purchasing The Repair Kit.

 

Note: The DIY Repair kit works with all brands of EIFS / Synthetic Stucco including Dryvit, Senergy EIFS, STO, Master Wall, etc.

We have been Exterior Insulation and Finish System repairs in Southeastern Michigan for over 26 years. We know why, when and how the system fails. Over the years we have seen it all.We have put this kit together from years of experience and testing. We have laterally written the book on the subject. With at least 12 classes and certifications on the subject you have someone that has put the time into being educated on the subject and the hands on experience of working in the field. Normally you are getting one or the other it is rare when you find both and that’s what you are getting when you buy the kit. Someone that has both the education and the hands on knowledge of a master of the industry. We have tested the methods and materials of this kit in the field our self literally hundreds of times and made tweaks and changes until it is a perfect kit for small home repairs like woodpecker holes.

The kit comes with 3 standard textures of finish which are fine finish, medium finish and coarse finish. Between the 3 we cover most all texture types. You will have to determine which texture is going to be best for your project. Picking the right texture is critical to having a nice looking patch when it is all finished. Remember that after your patch is completed you are going to paint the patch with paint you have matched at your local paint store. When you paint over the Synthetic Stucco it loses some of it’s texture. So, if you are stuck between a fine finish and a medium then go with the medium and after it is painted it will look more like the fine. We call those textures tweeners, because they are in between textures and are a real pain even for the pros, just do your best. There’s nothing more you can do.

The base coat in the kit takes a long time to setup, so you have plenty of time to use it at least 45 to an hour. On a real hot day though you can cut that in half. Always use cold water to make your mix. The most important part about the cement coat is to get it as smooth as possible. The finish coat is only a sixteenth of an inch thick so it will not cover to much. It is easier to run the classic finish as it is the thickest. That being said the fine finish is the hardest to make look good. Bottom line the better your base coat looks the better your patch will look.

The fiberglass mesh is important for you patch. If you don’t use the mesh the cement coat will crack. The fiberglass mesh is embedded into the base coat.

If you have pictures of your repairs you completed using the kit please send them to us we would love to see them. Send images click >>> Email Pictures

 

EIFS repair kit

© eifsrepair.info 2011 – 2016

– Plagiarism Warning

 

 

Back to the TOP

EIFS – Exterior Insulation and Finish System also known as Synthetic Stucco or Dryvit, the best product on the market when applied correctly.

Do It Yourself EIFS Repair Kit

 



How to match the color for an EIFS repair

How to match the color for an EIFS repair.

EIFS Repair ‘Tip Of The Day’ for 3-23-2011 – How to match the color of an EIFS repair


One of the hardest things with doing an EIFS repair is matching the color. As I have said in previous posts it is best to go coast-to-coast with all your patches. But, even then it is imperative that the new patches color matches with the rest of the building.  The best way to insure your patch is going to match the existing building is to cut a 3 ich by 3 inch square from the damaged area. I know that sounds bad to make the patch even bigger, but it is by far, the best way to make sure it is going to match. Even if you have the color code from the customer, that does not mean it is not going to be an exact match. The building has been done for some time, and the weather and other environmental conditions have faded the color to some degree.  Having the exact color that went on the building, and from what manufacturer is a great plus, and gives you a good place to start with the color, but some tweaking is going to be in order. Hopefully your local material house has a good color guy on staff. I usually spend a an hour or so with him getting the color exact.

Have a question visit our Contact page

back to EIFS Repair Tip Of The Day

EIFS Repair | How To | Exterior Insulation and Finish System | Synthetic Stucco | Dryvit | Senergy | Sto | Master Wall

 

How to match the color of an EIFS Repair
© eifsrepair.info 2011 – Plagiarism Warning

How to match the color for an EIFS repair.

The EIFS estimator has been featured on Brothersoft

The EIFS Estimator was release on April First and yes I know, but really it is no joke. The EIFS Estimator is really out and it works great there is no April fools here at all. ItEIFS Estimator Featured on Brothersoft - Free Download is already featured on one of the top download sites on the web – Brothersoft With more  software download sites to pick it up soon. I have made the EIFS Estimator completely free to use. After all we are here to educate and help the EIFS Industry and I believe the EIFS estimator will help many home owners and contractors.

If you have an EIFS (Exterior Insulation and Finish System) project you need a quote for feel free to use the EIFS Estimator totally free.

The EIFS Estimator is used for bidding EIFS (Exterior Insulation and Finish System) also known as Synthetic Stucco or Dryvit. Dryvit is actually one of the main manufactures of the EIFS product they promoted them selfs so much a lot of people think the industry is called Dryvit much like Rollerblade did with inline skates. But in fact there are several big players now in the EIFS Industry as for manufactures of the product which includes Senergy, Sto, Master Wall are a few of the big ones in the Mid West and of course Dryvit.

 

A good plasterer will use a Curry Trowel | EIFS

EIFS Repair ‘Tip Of The Day’ for 3-9-2011

A good plasterer will use a Curry trowel.

It is pretty common knowledge that Curry trowels are the best, well at least to all of us season vets of the plastering industry outEIFS Repair Curry Trowel there.  For everyone one else take my word for it, there is no better trowel on the market. If you are a EIFS guy, and you don’t have a Curry trowel in your tool bucket, then get you one you’ll love it. I personal use a 14 x 5 Curry Finishing Trowel which in my option is the perfect sized trowel for EIFS. It takes several months to break in a new trowel but after that you are golden with one of these trowels. It does not matter if you use Dryvit, Senergy, Master Wall, Sto or any other material a Curry trowel works the best with them all.

Back to EIFS Repair ‘Tip Of The Day’

EIFS Repair | Exterior Insulation and Finish System | Synthetic Stucco

EIFS Repair - plagiarism warning
© eifsrepair.info 2011 - Plagiarism Warning

EIFS Repair – How to float the finish

EIFS Repair – Tip of The day 3-6-2011

How to float the finish coat.

When floating the EIFS (Exterior Insulation and Finish System) Finish coat you will need a plastic float, a trowel and a clean bucket of water with a brush. You will rub the plastic float over the finish on the wall in a circular motion. Every few circles you will clean the plastic float with the trowel. You will do this two times the first time quickly with a firm grip and some pressure on the float making sure to hit every spot on the wall and taking any and all trowel lines away. The second time will be much lighter to clean up any imperfections. After the first round with the float you should make sure you clean the float with your clean water and bucket brush. It is important not to put the float back on the wall while it is wet.

EIFS | Exterior Insulation and Finish System | synthetic stucco | Dryvit | Senergy | Master Wall | Sto

 

More EIFS Repair Tip’s of the Day

 

EIFS Repair - plagiarism warning
EIFS Repair - plagiarism warning

 EIFS Repair – How to float the finish

Consistency of the Finish

EIFS Repair Tip Of The Day – 3-5-2011

The consistency of the finish

I think everyone has there own preference on the consistency of the finish but really if there is too much water added the finish will bleed through and if there is no water added it will  tend to roll on you. The best practice is to add a large cup of water like a 24 oz cup. If you are using tint packs with your finish that will give you enough water to make sure you get all the tint out of the tint pack. That is more of an estimate than a solid amount. If it is really hot you could even use 32 oz’s. One of the key things is to make sure you add the same amount to every bucket. I find Senergy, Dryvit and Master Wall all react about the same to the water.

EIFS (Exterior Insulation and Finish System / synthetic stucco) Tip Of The Day for 3-5-2011

back to EIFS Repair Tip Of The Day

 

plagiarism warning